ACTi D42 Handbuch

Bullet Camera Series Hardware Manual D41, D42, E41, E42, E43 E41A, E42A, E43A Ver. 2013/06/14

www.acti.com Hardware Manual 10 Installation Procedures Mount the Camera Using the Bundled Bracket 1. Mark the location of the th

www.acti.com Hardware Manual 11 4. Depending on how you want to install the camera, attach the camera to the bracket through one of

www.acti.com Hardware Manual 12 6. Connect an Ethernet cable from the network side to the Ethernet port of the camera to complete t

www.acti.com Hardware Manual 13 Other Mounting Options In areas with fierce weather conditions, the light bundled bracket can be rep

www.acti.com Hardware Manual 14 Waterproof Cable Installation The camera and the pre-installed network cable are resistant to salt w

www.acti.com Hardware Manual 15 Step 1: Remove the Pre-installed Network Cable (“Pigtail”) 1. Loosen the three (3) screws to detac

www.acti.com Hardware Manual 16 Step 2: Prepare the Conduit Gland and Flex Conduit 1. Disassemble the bundled conduit gland as sho

www.acti.com Hardware Manual 17 4. Insert the sealing insert and attach it at the end of the flex conduit. Step 3: Install

www.acti.com Hardware Manual 18 3. Secure the clamping nut to the body. Step 4: Connect the Ethernet Cable 1. Connect the Ethe

www.acti.com Hardware Manual 19 Replace the Pre-Installed Network Cable The pre-installed network cable comes with an Ethernet p

www.acti.com Hardware Manual 2 Table of Contents Precautions 4 Safety Instructions ...

www.acti.com Hardware Manual 20 Step 1: Remove the Pre-installed Network Cable (“Pigtail”) 1. Loosen the three (3) screws to detac

www.acti.com Hardware Manual 21 Step 2: Install the New Ethernet Cable 1. Insert the new Ethernet cable through the sealing nut, c

www.acti.com Hardware Manual 22 5. Tighten the sealing nut. NOTES on using Ethernet cables: When replacing the pre-installed ne

www.acti.com Hardware Manual 23 Basic Connections To connect the camera, you need to prepare the following:  Power over Ethernet (

www.acti.com Hardware Manual 24 Connecting Multiple Cameras To connect multiple cameras, use a PoE switch.

www.acti.com Hardware Manual 25 Accessing the Camera Configure the IP Addresses In order to be able to communicate with the camera f

www.acti.com Hardware Manual 26 launch the default browser of the PC with the IP address of the target camera filled in the address

www.acti.com Hardware Manual 27 Using the Default Camera IP Address If there is no DHCP server in the given network, the user may ha

www.acti.com Hardware Manual 28 Manually adjust the IP addresses of multiple cameras: If there are more than 1 camera to be used in

www.acti.com Hardware Manual 29 Access the Camera Now that the camera and the PC are both having their unique IP addresses and are u

www.acti.com Hardware Manual 3 Other Adjustments and Accessories 31 Adjust the Viewing Angle ...

www.acti.com Hardware Manual 30 Assuming that the camera’s IP address is 192.168.0.100, you can access it by opening the Web browse

www.acti.com Hardware Manual 31 Other Adjustments and Accessories Adjust the Viewing Angle 1. Open the front cover. 2. Based

www.acti.com Hardware Manual 32 Attach the Sunshield The use of sunshield is optional if the camera will be installed indoors. Howev

www.acti.com Hardware Manual 33 Appendix How to Make an Ethernet Cable 1. Prepare the following tools:  Ethernet cable without co

www.acti.com Hardware Manual 4 Precautions Read these instructions You should read all the safety and operating instructions before

www.acti.com Hardware Manual 5 Federal Communications Commission Statement This equipment has been tested and found to comply with t

www.acti.com Hardware Manual 6 Safety Instructions Don’t open the housing of the product Cleaning Disconnect this video product fro

www.acti.com Hardware Manual 7 Introduction List of Models This hardware manual contains the following models: D41 1MP Bullet with

www.acti.com Hardware Manual 8 Package Contents Bullet Camera Sunshield Conduit Gland Mounting Screw Kit Sunshield Screw Kit Q

www.acti.com Hardware Manual 9 Physical Description 1) Reset Button Use the Reset Button to reset the camera to its factory defau