2013/12/03 Outdoor Hemispheric Mounting on a Vertical Pole Using the Tilted Mount Installation Guide For Models: KCM-7911
www.acti.comInstallation Guide 10 Step 6: Install the Camera to the Tilted Mount 1. If necessary, insert a memory card into the card slot of the
www.acti.comInstallation Guide 11 Step 7: Close the Cover Tighten the three (3) screws to secure the cover. Step 8: Access the Camera Live Vie
www.acti.comInstallation Guide 12 Installation Procedures using Flex Conduit This section provides step-by-step procedures in installing the camer
www.acti.comInstallation Guide 13 3. Do steps 1 and 2 to the other wire strap. 4. Position the pole mount with the cable path up and encircle
www.acti.comInstallation Guide 14 Step 2: Attach the Tilted Mount Attach two (2) screws (included in the pole mount package) to secure the tilted
www.acti.comInstallation Guide 15 3. Lift to open the cover. NOTE: Do not abruptly lift the cover; it is attached to the camera body with a spri
www.acti.comInstallation Guide 16 3. From the network side, route the flex conduit to pass through the pole mount and tilted mount. 4. Insert t
www.acti.comInstallation Guide 17 7. Attach the lock nut to secure the conduit gland body to the camera. 8. Insert the Ethernet cable and other
www.acti.comInstallation Guide 18 10. Insert the sealing rubber into the conduit gland body and attach the clamping nut to complete the cable solu
www.acti.comInstallation Guide 19 Step 5: Install the Camera to the Tilted Mount 1. If necessary, insert a memory card into the card slot of the
www.acti.comInstallation Guide 2 Table of Contents Mounting Solutions ... 3 Installation
www.acti.comInstallation Guide 20 Appendices This section describes the procedures in preparing the external devices that you can connect to the c
www.acti.comInstallation Guide 21 3. Connect the wire with the white stripe to the 12V pin and the other to the GND pin. 4. Tighten the scr
www.acti.comInstallation Guide 22 Connecting DI/DO Devices (Optional) Depending on your surveillance needs, you may connect digital input or outpu
www.acti.comInstallation Guide 23 To connect output devices (DO), map the pins to one of the pin combinations below: Device Pin Mapping Instruct
www.acti.comInstallation Guide 24 High Voltage DO Device Connection Even though the camera provides 12V power, this may not be enough for some hi
www.acti.comInstallation Guide 25 Connecting Audio In / Out Devices (Optional) Depending on your surveillance needs, you may connect audio input o
www.acti.comInstallation Guide 26 Safety Information Read these instructions You should read all the safety and operating instructions before usin
www.acti.comInstallation Guide 27 Damage Requiring service Disconnect this video product from the power supply immediately and refer servicing to
www.acti.comInstallation Guide 3 Mounting Solutions The camera can be mounted on a vertical pole with the camera facing forward using the Pole Mou
www.acti.comInstallation Guide 4 Installation Procedures using Naked Cable This section provides step-by-step procedures in installing the camera
www.acti.comInstallation Guide 5 3. Do steps 1 and 2 to the other wire strap. 4. Position the pole mount with the cable path up and encircle t
www.acti.comInstallation Guide 6 Step 2: Attach the Tilted Mount 1. Attach two (2) screws (included in the pole mount package) to secure the tilt
www.acti.comInstallation Guide 7 2. Disassemble the cable gland as shown below: 3. Insert the clamping nut into the Ethernet cabl
www.acti.comInstallation Guide 8 Step 4: Open the Camera Cover 1. Loosen the three (3) screws using the supplied hex wrench. 2. Lift to open th
www.acti.comInstallation Guide 9 Step 5: Connect the Cable(s) 1. Insert the Ethernet cable through the cable gland body and connect it to the Eth
Kommentare zu diesen Handbüchern